Skip to content

Remove tree stump with stump grinder — Which Machine, Which Providers?

Recommended class
Mini (1-2t) mit Wurzelreißer
Typical duration
1 Tag
Cost estimate
150-400 €

Overview

A tree stump left in a lawn or driveway isn't just an eyesore — it's a tripping hazard, it blunts mower blades, and it can keep sending up new shoots for years. Stump grinding solves this by mechanically chewing the stump down below ground level using a rotating cutting wheel, rather than digging it out whole. For most domestic jobs — a single stump up to roughly 40-50cm in diameter, in a garden with reasonable access — a mini stump grinder in the 1-2 tonne class is the right tool. These machines are narrow enough to pass through a standard side gate, light enough to tow on a small trailer, and still have enough cutting power to get a stump well below soil level in a few hours.

Larger jobs change the picture. Multiple stumps, very large or old hardwood stumps, or root systems that need to be pulled rather than ground call for a compact or standard-class machine with a root rake or stump grinder attachment on a mini excavator (typically 3-5t). This approach rips the stump and major roots out of the ground entirely, which is useful if you're preparing the area for new foundations, paving, or planting where root remnants would be a problem. For a single garden stump, though, most UK homeowners either hire a dedicated stump grinder for a day or bring in a local tree surgeon or groundworks contractor who already owns the equipment. A typical job — hire, fuel, waste removal, and backfilling the hole — takes a single day and costs somewhere between £130 and £350 depending on stump size, access, and whether you do it yourself or pay for a crew.

Step-by-step

  1. 1. Assess the stump and site

    Measure the stump diameter and check how close it is to walls, drains, cables, or buried services. Note root flare direction and whether the ground slopes. This determines whether a mini stump grinder is sufficient or whether you need a machine with a root rake to pull out larger root plates. If you're unsure about buried utilities, get them marked before digging or grinding begins.

  2. 2. Clear the working area

    Remove stones, low branches, garden furniture, and any debris within a few metres of the stump. Stump grinders throw out a steady stream of wood chips and soil at speed, so clear glass, fences you want to protect, and parked vehicles well back. Lay down boards or a tarpaulin if you want to make clean-up of the chippings easier afterwards.

  3. 3. Cut the stump down low

    If the stump stands more than 15-20cm proud of the ground, use a chainsaw to cut it as low as practical first. This reduces the amount of grinding needed and lets the machine work more efficiently from the start, rather than chewing through unnecessary bulk.

  4. 4. Grind the stump in passes

    Lower the cutting wheel onto the stump and work it side to side in controlled passes, advancing a few centimetres with each pass rather than plunging straight down. Grind to at least 20-30cm below soil level if you plan to replant or lay turf over the spot, since shallow grinding often leaves roots that resprout or settle later.

  5. 5. Remove or rake out chippings

    Rake the wood chip and soil mix out of the hole. Keep some aside if you want to use it as mulch elsewhere, since it breaks down well over time. The rest typically needs to go to green waste disposal, as it's not accepted as general rubbish in most areas.

  6. 6. Backfill and reinstate the ground

    Fill the remaining hole with topsoil, firm it down in layers to avoid future sinking, and reseed or turf as needed. Expect some further settlement over the following weeks as remaining roots decompose, so a follow-up top-up of soil is common.

Cost breakdown

Mini stump grinder hire (1 day)£60-£120Self-hire from a plant hire centre, excludes fuel and delivery
Delivery and collection£30-£60Often charged per trip if the machine isn't collected by you
Fuel (petrol or diesel)£10-£20Depends on stump size and grinding time
Contractor/tree surgeon (supply & operate)£100-£300Flat rate common for single stumps; cheaper per stump for multiples
Green waste disposal£0-£40May be free if chippings are kept on site as mulch
Topsoil for backfilling£10-£30Per bulk bag, depending on hole size
Public liability insurance (self-hire)£0-£15Sometimes included in hire terms, check before booking

Common pitfalls

  • Grinding only to ground level instead of 20-30cm below — leaves roots that resprout or cause the ground to sink later.
  • Not checking for buried cables or pipes near the stump — a struck service can mean repair costs running into hundreds of pounds and a safety risk.
  • Underestimating root spread on older trees — a grinder sized for the visible stump diameter may still struggle with a wide root plate, extending the job well past the planned time.
  • Skipping eye and ear protection — flying chips and stones from the cutting wheel travel fast and far enough to cause injury.
  • Hiring a machine too large for garden access — a compact or standard-class grinder that can't fit through a side gate means wasted hire costs and a rescheduled job.
  • Leaving chippings in a pile without arranging disposal — green waste often can't go in general bins, leading to extra trips or fees later.

FAQ

Do I need planning permission to remove a tree stump?
Generally no permission is needed to remove a stump itself, but if the tree was subject to a Tree Preservation Order (TPO) or sits within a conservation area, the original felling or removal of the tree may have required consent — and some TPOs also cover removal of remaining stumps or regrowth. Check with your local planning authority if there's any uncertainty, as this applies to the tree's status rather than the grinding work itself.
How much does stump grinding typically cost in the UK?
For a single garden stump, expect to pay roughly £130-£350 all-in if you hire a self-hire mini grinder and do the work yourself, including fuel, delivery, and waste disposal. Hiring a tree surgeon or groundworks contractor to supply the machine and do the job typically costs £100-£300 per stump, often less per stump if you have several done at once.
What size stump grinder do I need for a typical garden stump?
A mini stump grinder (roughly 1-2 tonne equivalent class, often towable or wheel-mounted) handles most garden stumps up to around 40-50cm in diameter comfortably. For wider stumps, multiple stumps, or where you also need the root ball pulled out of the ground entirely, a mini excavator fitted with a root rake or grinder attachment is a better fit.
Should I grind a stump myself or hire a professional?
DIY self-hire works well if you have one accessible stump, are comfortable operating power equipment safely, and can arrange waste disposal yourself. It's usually cheaper. A professional is worth it for larger or multiple stumps, stumps near buildings or services, or if you want the job done in a single visit without handling fuel, transport, and clean-up yourself.
How deep should a stump be ground down?
For most purposes, grinding 20-30cm below soil level is recommended. This allows enough depth for backfilling with topsoil and reduces the chance of regrowth or future settling as the remaining root material decomposes. If you plan to build a structure or lay a hard surface over the spot, deeper grinding or full root removal with an excavator is usually a better approach.
How long does it take to grind a tree stump?
A single stump typically takes 1-3 hours of actual grinding time depending on diameter, wood hardness, and root spread, but the job is usually planned as a full day once you include machine delivery, setup, grinding, raking out chippings, and backfilling.
Stump Grinding Cost & Machine Guide (£130-£350, 1 Day) — Construction Equipment Today